DEVELOP Training Center (TM) menyelenggarakan Kelas LPG Pressure Vessel Design,Fabrication,Inspection&Construction Training yang akan melatih Anda untuk mendapatkan skill tentang :
- Merancang, memeriksa & membangun Pressure Vessel Penyimpanan LPG dengan peralatannya serta menavigasi dan mengoptimalkan desain rekayasa LPG Storage
- Memahami detail konstruksi Terminal Penyimpanan LPG
- Memahami Bagian & komponen internal LPG Storage
- Memahami inspeksi/pengujian & pemeriksaan LPG Pressure Vessel Storage
Pembahasan materi mengetengahkan contoh-contoh latihan dalam konteks dunia proyek konstruksi sehingga lebih familier dengan aktivitas proyek sehari-hari.
Materi Training di DEVELOP Training Center (TM) dirancang khusus oleh para praktisi designer & engineer sesuai dengan kebutuhan project. Anda akan mendapat sharing ilmu langsung dari para praktisi yang berpengalaman.
DEVELOP mengimplementasikan Syllabus LPG Pressure Vessel Design,Fabrication,Inspection&Construction Training dengan tahap-tahap pembelajaran berkualitas sbb :
Sesi 1-2
Skill Focus:
- Introduction to LPG Storage, Accessories and Water Spray System
- LPG Pressurized Storage: Aspek Design Aspek Fabrikasi, Inspeksi dan Konstruksi
- Reference Codes or International Standard
- API Standard 2510, Design and Construction of LPG Installation
- API Publication 2510a, Fire Protection Considerations for the Design and Operation of Liquefied Petroleum Gas (LPG) Storage Facilities.
- ASME Section VIII, Division 1 and Division 2 for Pressurized Storage Tank Design.
- LPG Characteristic&Design EXERCISE
- Mixture of propane and butane (about 70% and 30%).
- Exist as vapor under ambient temperature.
- Flammable and heavier than air
- Large vapor to liquid ratio
- Non corrosive
- Normally having specific gravity 0.49 to 0.57 (as liquid)
- Loadings & Stresses
- Design of Shell & Heads
- Design of Openings
- Support Design
Sesi 3-4
Skill Focus:
- LPG Storage Design
- Design and construction of LPG Vessel shall meet requirement of the ASME Code, Section VIII, Division 1 or Division 2. In general, ASME Codes are applied as follow:
- ASME Section VIII Division 1, applied for Horizontal Vessel
- ASME Section VIII Division 2, applied for Spherical Tank
- Spherical Pressurized LPG Tank and Bullet Tank
- Minimum distance requirement API Standard 2510
- Sitting of Pressurized LPG Tanks and Equipment
API Standard 2510- LPG Tanks Accessories
API Standard 2510 Section 7: Liquid-Level Gauging Equipment & Max. Liquid Level- LPG Tanks Accessories
API Standard 2510 Section 7: Pressure Gauge and Level Gauge- LPG Tanks Accessories
API Standard 2510 Section 7: Shut off Valves- LPG Tanks Fire Protection
API Standard 2510 Section 10: Water Spray System- LPG Nondestructive Examination NDE RT/UT/MT/PT
- LPG Pneumatic Test
- LPG Proof Test
- Case Study
Materi Training di DEVELOP Training Center (TM) dirancang khusus oleh para praktisi designer & engineer sesuai dengan kebutuhan project. Anda akan mendapat sharing ilmu langsung dari para praktisi yang berpengalaman.
Selama training, instruktur kami akan menggunakan kombinasi teori serta praktek langsung dengan studi kasus telah dipersiapkan yang menyerupai Proyek nyata.
QUICK REGISTER :
Important Job Skills You Can Learn for Works :
ASME VIII Division 1 Pressure Vessel Fundamental Comprehensive&Understanding Training
Unfired Pressure Vessel Design,Fabrication&Inspection Workshop
API-510 PRESSURE VESSEL INSPECTOR Certification Preparation Training
Mechanical System Design&Installation Pressure Vessel/Bejana Tekan Training
Pressure Relief Valve PSV Inspection&Maintenance Workshop
Inspektor Bejana Tekan/Pressure Vessel Inspector
BS EN-5500 Pressure Vessel Design&Installation Workshop
LNG Storage Tank Design&Construction Training
Predictive Maintenance Pressure Vessel/Bejana Tekan Training
ASME PCC-2 Repair of Pressure Equipment&Piping Training
